Sunday, August 3, 2014

HCL ME U2 Firmware, STOCK ROM


Before you proceed flashing / hard resetting your phone / tablet make sure to back up your important files if possible. Because we care about your data.

We also suggest that your battery should be atleast 50% or better to have it fully charge, lower than the said value may cause unwanted result, such as bricking your phone / tablet rendering it unuseable. This is very important in flashing your phone / tablet. Use original USB cable as possible.

Files that you downloaded should not be corrupted, if ever the file is corrupted you might brick your phone. Or the flashing will start.

Drivers are very important specially in Spreadtrum Chipset, having an Spreadtrum SPD6610 (non android devices) driver will not work in SPD6820 (android devices).

If you are using laptop to flash your phone, make your that it has enough charge. If your laptop shutdown when your flashing your phone/tablet, you'll end up bricking your phone. Sometimes you can still recover your phone just flash it again and your phone will boot up again. But that is just a case to case basis, if your phone / tablet is deadboot (totally dead, erased all program in the chip) you can't recover it, you will need to seek professional help (technician).





This is the firmware/stock rom for HCL ME U2, you can use in Android System Recovery to flash your tablet. This can fix the following issue.

1. Hang in Android Logo.
2. Deleted System Apps.



Ok lets do it. Just follow the procedure

  1. Download the file here and extract it –--->>>> Here
  2. After downloading copy the update.zip in your memory card.
  3. Then boot into recovery mode by pressing volume down + power button
  4. an Android logo will appear, just wait until it goes to android system recovery
  5. In android system recovery select “Apply update from sdcard” and locate the u2 firmware. Wait until its done.
  6. Reboot your tablet.

That's it your phone is back in its original state.

30 comments:

  1. My tab stuck @ boot...not even recovery I can work out...help me please

    ReplyDelete
  2. Hi Sudeep, you can only flash this firmware via Stock Recovery, I don't the the rom to flash in Livesuit.

    ReplyDelete
  3. Hi Maribel...thanks for the reply...but how do I move further...coz its stuck in downloading mode...not into recovery too

    ReplyDelete
  4. Yes I do reply always, hmmm that's strange, can you try to press and hold VOLUME DOWN and Power Button, just keep on pressing it until you see an android Logo,

    If it still stuck in Downloading Mode, try to press the buttons.

    Or try VOLUME UP and Power Button.

    ReplyDelete
  5. Have tried both..but of no use... tab switches on to ODIN download mode :( ....and nothing further and my PC jus detect the IN-built Media storage of 8 GB daats all...

    ReplyDelete
  6. dis is where it stucks...

    ReplyDelete
  7. dis is wher it stucks..

    ReplyDelete
  8. I see, I'm not really sure if the stock recovery is damaged.

    ReplyDelete
  9. hi Sudeep, before the android logo did you an upgrading...please wait warning?

    if it is stuck in the android logo, just wait for it until it reboots.

    ReplyDelete
  10. Just wait my coworker said that you just have to wait until the Android Recovery to appear.

    ReplyDelete
  11. its not going into recovery..whole day it stuck on the same logo...

    ReplyDelete
  12. what next if stock recovery is damaged..??

    ReplyDelete
  13. i dont know a firmware that you can flash it via livesuit...


    that is the only way to recover your tablet...

    ReplyDelete
  14. do you have USB drivers for windows 7 for HCL ME U2

    ReplyDelete
  15. hi sudeep, you can try vroot, it automatically download the driver that is needed for your phone and tablet...

    http://d-h.st/0oE i hope it works.

    ReplyDelete
  16. thanks.....I guess I am having bad luck here I guess.....Vroot needs USB dubug mode...but I am not able to move on from the android logo... :)

    ReplyDelete
  17. Tough luck!, I hope that I help you more. But that is all I can do for now.

    ReplyDelete
  18. thanks for the replies.......let you know IF i can solve it... :)

    ReplyDelete
  19. hi all, any latest firmware for HCL Y3, i download 1 update but touch scree is not working and also i lost original firmware came with Tab.
    thanks in advance.

    ReplyDelete
  20. thank you
    the tabe now work again

    ReplyDelete
  21. you are welcome :) mostafa :)

    ReplyDelete
  22. hello,
    please can u tell me how to flash hcl me connect v3

    ReplyDelete
  23. HCL ME U2 tried to flash ROM from U2_image as your instructions but "installation aborted" with this msg:
    E: Error in /tmp/sideload/package.zip
    (Status 7)
    could you please help me?

    ReplyDelete
  24. not show recovery mode plz help me.

    ReplyDelete
  25. press power key and volume - key in same time for 3 second In hcl tab

    ReplyDelete
  26. Hai! I am at the reboot step but if i reboot it stills stay on logo

    ReplyDelete
  27. hi my hcl me sync 1.0 dont want to open recovery mod

    ReplyDelete
  28. hi my hcl me sync 1.0 dont want to open recovery mod

    ReplyDelete

 

Subscribe to our Newsletter

Contact our Support

Email us: gadgetzboyz@gmail.com

Our Team Memebers