Just Another Gadget Blog

Breaking

Saturday, July 5, 2014

SKK A11 Remove Pattern Lock, Reset

Before you proceed flashing / hard resetting your phone / tablet make sure to back up your important files if possible. Because we care about your data.

We also suggest that your battery should be atleast 50% or better to have it fully charge, lower than the said value may cause unwanted result, such as bricking your phone / tablet rendering it unuseable. This is very important in flashing your phone / tablet. Use original USB cable as possible.

Files that you downloaded should not be corrupted, if ever the file is corrupted you might brick your phone. Or the flashing will start.

Drivers are very important specially in Spreadtrum Chipset, having an Spreadtrum SPD6610 (non android devices) driver will not work in SPD6820 (android devices).

If you are using laptop to flash your phone, make your that it has enough charge. If your laptop shutdown when your flashing your phone/tablet, you'll end up bricking your phone. Sometimes you can still recover your phone just flash it again and your phone will boot up again. But that is just a case to case basis, if your phone / tablet is deadboot (totally dead,  erased all program in the chip) you can't recover it, you will need to seek professional help (technician).


Did you forgot your google account or you cannot enable the data connection so that you can enter your google account to your phone to recover your phone.

In this tutorial we will remove the pattern lock of your phone (SKK A11). Just follow the instructions carefully so that you can fully restore your phone into its normal state.

*** Note: I am not responsible for bricking your phone, files uploaded are proven tested to support SKK A11 regardless of the phone color.

Lets proceed. Download First the 3 files.
Research Download ----> Here
UserBlock ------> Here
Spreadtrum Driver -------> Here

After downloading the 3 files. Extract it in one folder. 
1. Open Research Download
2. Load Packet, it is the first button in Research Download, look for SKKA11 file that you extracted. It is usually .pac format.
3. Check the following below: ONLY THE THREE
FDL1FDL2UserData
4. Click in Calibration Page, in Research Download. And UnCHECK ALL
5. Press OK, and Press Play Button.

Check Picture for you reference






To Connect your phone.
1. Press Volume Down or Volume UP and Hold it.
2. Insert USB Cable while holding Volume UP or Down
3. This time your computer might need the driver, you can find the driver in Spreadtrum.rar file and install the necessary file that is needed.
4. This time the Research Download should detect your phone and continue flashing/resetting your phone.

I hope this tutorial helps. If you have any questions just drop a comment.

52 comments:

  1. Hi, there is no available firmware for cherry mobile 2.0, You can use the firmware for 1.0 but wifi and bluetooth will not work.


    You can recover your phone using VolcanoBox if you have one, I did not manage to recover it using ResearchDownload but you can try.

    ReplyDelete
  2. what should be the status mine is Downloading how long is it?

    ReplyDelete
  3. when i used this tutorial it keeps downloading and then end in FAILED? what should i do?

    ReplyDelete
  4. When you press the play button, it should flash about 1 minute...

    ReplyDelete
  5. Why my SKK A11 cannot pass using bluetooth?? Please Help me...

    ReplyDelete
  6. is there an error when you are activating the bluetooth? can you search your phone using other phone?

    did you turn on the discoverability?

    ReplyDelete
  7. its not working with my skka11:(

    ReplyDelete
  8. what is the error? can i see it?

    ReplyDelete
  9. Franc Gallo SumampongDecember 15, 2014 at 8:38 AM

    boss bakit po na unpluged ung unit ko anung problema dito may mali po sa ginawa ko?

    ReplyDelete
  10. try niyo lang po ulit.... baka nagagalaw lang yong sa usb port,...

    ReplyDelete
  11. Franc Gallo SumampongDecember 16, 2014 at 12:41 AM

    KELANGAN BA TLAGA NA NKA STEADY LNG ANG PINDOT KO SA POWER BUTTON AT VOL.DOWN? TY PO^

    ReplyDelete
  12. Franc Gallo SumampongDecember 16, 2014 at 11:45 AM

    ok ill try salamats ng marami^^

    ReplyDelete
  13. Franc Gallo SumampongDecember 16, 2014 at 1:01 PM

    ganun pa rin eh

    ReplyDelete
  14. Franc Gallo SumampongDecember 16, 2014 at 1:32 PM

    anu po ba ibig sabihin ng,,, failed:wait input time end hangang dito lng kasi ako

    ReplyDelete
  15. Franc Gallo SumampongDecember 16, 2014 at 1:36 PM

    may dapat ba akong echeck sa flash operations?

    ReplyDelete
  16. anong OS po gamit ninyo? Windows 7 ba? at 32bit din ba?

    ReplyDelete
  17. ang last resort mo iflash mo nalang yong buong firmware, meron ako dito non sa blog ko. yong SKK A11 Stock ROM search mo nalang po sa search box.

    ReplyDelete
  18. Franc Gallo SumampongDecember 16, 2014 at 4:44 PM

    OPO WIN 7 32 BIT

    ReplyDelete
  19. Franc Gallo SumampongDecember 19, 2014 at 1:30 AM

    pano iflash po yun? hehe cnxa noobs^^ pde penge ng screen shoot ng flashing? ty

    ReplyDelete
  20. halos same lang, wala ang gagalawin mo lang yong sa calibration...

    ReplyDelete
  21. Franc Gallo SumampongDecember 19, 2014 at 9:54 AM

    anu po e check ko dun sa calibration?

    ReplyDelete
  22. uncheck mo lang lahat yon...

    ReplyDelete
  23. Franc Gallo SumampongDecember 19, 2014 at 11:52 PM

    ok sir noted,,, pag di ko mgawa i teamviewer kita salamats ^^

    ReplyDelete
  24. hindi ko ma-install driver sa win 8.1 :( kun gagamit ba ako ng vmware?

    ReplyDelete
  25. eto po https://www.sendspace.com/file/egfyj8

    ReplyDelete
  26. bakit di ko makita ang .pac file?

    ReplyDelete
  27. na DL ko na lahat ng files pero di ko makita ang pac file sa research download .. pa help poh

    ReplyDelete
  28. pindotin mo po yong first button sa research download para maiload mo po ito.

    ReplyDelete
  29. hi sir. pa help naman po. pag kaopen ko sa .pac file. laging bin not supported. win7 po OS ko at 64bit

    ReplyDelete
  30. Sir sensya na hindi ata pwede sa 64bit ang researchdownload.... May nagtry din kasi dito dati. Hindi tumutuloy sa flashing.

    ReplyDelete
  31. pwede po kayo to sa win XP?

    ReplyDelete
  32. pwedeng pwede po.... tested ko naman sa XP kasi gamit ko naman ay XP :)

    ReplyDelete
  33. ok tnx po. try ko sa compshop dito

    ReplyDelete
  34. ok.. pwede rin kita iteamviewer kung gusto mo... :)

    ReplyDelete
  35. Bakit bin version not support? Win 7 Ultimate x64 OS ko..

    ReplyDelete
  36. Pa check naman ano problem dito ? Thanks.

    ReplyDelete
  37. pang 32bit lang po ang researchdownload...

    ReplyDelete
  38. pang 32bit lang po ang researchdownload.

    ReplyDelete
  39. di ko maLoad yung pac files :(

    ReplyDelete
  40. patry nalang po ulit. may topak kasi dyan sa sendspace minsan :D

    ReplyDelete
  41. pdii pong phelp! dku npo kasi mabuksan phone ku. nlmutanq yung password. skk A11.

    ReplyDelete
  42. Hard reset lang po iyan sa recovery pa try po

    ReplyDelete
  43. Sundan niyo lamg po yang sa taas.

    ReplyDelete
  44. Walq pong hard reset ang skk a11

    ReplyDelete
  45. Try u po off tapos on combination ng volume up and power sabay po dapat lumabas po recovery

    ReplyDelete
  46. Dapat po pag bagong cp i back up agad sa recovery para sa ganun po ay pag naka roon ng problema mabilis ang solution

    ReplyDelete
  47. If na wala po hard reset ready nyo na po for flashing cp nyo

    ReplyDelete
  48. Joshua Ponciano VargasMay 19, 2015 at 5:34 PM

    hindi ko po magawa yung instruction sa taas?? :(
    how can i fixed my skka11 :(

    ReplyDelete
  49. Sir, patulong naman po, nag chacharge lang po kapag connect to pc po.

    ReplyDelete
  50. sikat kana bossing. ikaw na ang magaling.

    ReplyDelete

Pages